English

Best Way To Fix Oki C5900 Belt Life Error

Table of Contents

You may see an error message stating oki c5900 belt life. As it turns out, there are several ways to fix this problem, so let’s talk about that now.

Fix PC Errors in Minutes

  • Step 1: Download and install ASR Pro
  • Step 2: Open ASR Pro and click the "Scan" button
  • Step 3: Click the "Restore" button to start the restoration process
  • This software will fix your PC - download it now to get started.

    “CHANGE BELT” / “BELT LIFE” Is Indicated. (C332)

    ANSWER

    Fix PC Errors in Minutes

    Looking for a powerful and reliable PC repair tool? Look no further than ASR Pro! This application will quickly detect and fix common Windows errors, protect you from data loss, malware and hardware failure, and optimize your system for maximum performance. So don't struggle with a faulty computer - download ASR Pro today!


    If “BELT LIFE” / “CHANGE BELT” is displayed and it prevents printing, replace the belt.

    You can still print while the “LIFE BELT” message is displayed by starting and closing the output tray. However, it is recommended to replace the belt as it may damage the underlying unit.

    Read the following information about replacing the ribbon assembly.

    Note

    oki c5900 belt life error

    Use the belt until the end of its life, then remove it and start over.

    If the removed belt is actually used in other devices, the lifespan of the device will not be displayed correctly.

    Note

    • The green drum tube is very dangerous, so be very careful with it.

    • Do not expose the imaging drum to direct sunlight or strong light (about 1500 lux or more). No

    • Go outside for more than 5 minutes and possibly with room light.

    • Avoid touching all fuser units as they are comfortable. ã €€

    1. Press the shutter button (a) and open the output tray (b) fully.

      Note

      If I say the printer is on, the fuser is hot. This area is clearly marked. You don’t have to touch it completely.

    2. Grasp the handles and use the image drum, which is fully loaded with toner cartridges, up and presumably outside the printer.

    3. Install the assembly in a safe place away from direct exposure to heat or light.

      Note

      The green imaging drum surface along the entire length of each cartridge is very intimate and sensitive to light. Do not bump it or expose it to normal room light for more than 5 minutes. If you do not need to keep the drum in the printer for a long time, simply wrap the cartridge in a dark plastic bag to protect it from light. Never expose the drum to direct sunlight.Teach or bright indoor or indoor lighting.

    4. Pull the locking levers on the side of the transfer belt and towards the front of the device at the same time.

    5. oki c5900 belt life error

      Raise the belt (b) using the locking levers (a), then remove it from the machine.

    6. Use this special gear to lower the handpiece belt assembly back to the printer. Insert the drive clothes into the gear inside the printer a at the rear right corner of the machine and lower the belt into the printer a.

    7. Move the levers towards the rear of the machine. This will tighten the belt on the unit.

    8. Holding the drum symbol by the sides, lower it into the machine and place the handles on all sides into the corresponding slots on the corresponding sides of the printer cavity.

    9. Close the output tray and hold it firmly to close the latches.

    Press down on the output cover (a) and open the output tray (b) fully.

    Note

    If printp has been turned on, the fuser will be very hot. This area is clearly marked. Don’t touch him

    While holding the explanations, lift the image drum and toner cartridges up and out of the printer.

    Install the assembly in a particularly safe location, away from sources of heat and light.

    Note

    The green surface of the waste drum at the bottom of all cartridges is very delicate and even sensitive to light. Do not touch anything or expose it to normal room light for more than 5 minutes. If the drum is not to be left in the laser printer for a long time, wrap the cartridge in a black plastic bag to protect it from light. Never expose the drum to strong sunlight, indoor or strong light.

    Pull the side locking levers of each transfer belt towards the front of the machine.

    Lower the new belt with the pinion gear towards the back of the printer. Insert the specific drive gear into the home printer gear in the rear right corner It is best to place the belt assembly in the printer.

    Hold the imaging drum close to the handles, lower it onto the machine table, and insert the new handles on the sides of the video poker machines into the sides of the printer’s ink tanks.

    Close the output tray and push all the way down to lock the insurance cover.

    WILL THE FAQ SOLVE YOUR PROBLEM?

    This software will fix your PC - download it now to get started.